A Shepherd company - serving Boulder City, NV

Owens Corning Ridge Vent Installation in Boulder City, NV

Owens CorningOwens Corning
Architectural shinglesArchitectural shingles
Metal roofingMetal roofing
Tile roofingTile roofing
GAFGAF
Flat & low-slopeFlat & low-slope
Every visit starts with

Free roof inspection with deck photos before we talk money - GAF and Owens Corning certified installation

We have financing partners for your new roof*On approved credit; ask us about your options
Get your free estimate

Owens Corning Ridge Vent Installation: The Boulder City Owner’s Guide

We install Owens Corning ridge vent systems in Boulder City, and most homes run $420 to $850 for a full ridge line, materials and labor together. When the vent is the only item on the ticket, the job is usually a single visit. If the ridge vent failed because shingles around it let go too, that’s a bigger conversation.

Contractors using a portable gutter forming machine for seamless gutter fabrication. in Boulder City, NV

Call (844) 761-8186

Most Boulder City owners find out the hard way. They go up in the attic in July and it’s hot enough to bake bread. Or they see daylight tracking along the ridge from inside. Then the shingles start curling near the peak before anything else, because that’s where the heat stacks up. A ridge vent that isn’t pulling air shows itself up there first.

Which Owens Corning Models This Applies To

Owens Corning ridge vents aren’t one product. The line has run through several generations, and the model on your roof depends on when it went on. The most common ones we pull in Boulder City are the rigid plastic and fiber-reinforced vent sections sized to standard ridge caps, usually 4-foot lengths that nail over the ridge with a filter layer underneath. Some versions are shingle-over, meaning the top course of shingles caps the vent. Others are narrower profile. Measure your ridge width and the vent’s overall footprint before you order anything.

The model label is usually stamped on the underside of a section near a gable end, or on the original packaging stapled into the attic near the ridge. If the label is gone, measure the vent’s external width and the spacing of the nail flanges. That tells you what it will replace.

On the OEM-versus-aftermarket question: Owens Corning’s own vent sections match their ridge cap shingles cleanly, which matters on a shingle-over install. Quality aftermarket equivalents in the same footprint exist and can save money. The catch is the filter layer and the nail flange spacing. Mismatched flanges push nails into the wrong spot and you get a leak before the year is out. If you already have Owens Corning shingles on that ridge, we stay with the matching vent where we can.

We install ridge vent across GAF and CertainTeed roofs too, so the shingle name on your house doesn’t lock you out of this conversation.

Explore

Styles & brands we work with

  • Architectural shingles
  • Metal roofing
  • Tile roofing
  • GAF
  • Owens Corning
  • Flat & low-slope

Signs Your Owens Corning Ridge Vent Installation Is Failing

  • Ridge shingles curling or cracking first. That ridge is the hottest point on the roof and the vent’s outlet. If the vent is clogged or under-sized, heat backs up and bakes those shingles years before the field shingles give out.
  • Attic feels like an oven in July. When a ridge vent stops moving air, the attic temperature climbs fast in Boulder City’s summer. The vent works with the soffit vents, so if either side is blocked, the whole system stalls.
  • Daylight or water at the ridge from inside the attic. That points to a nail driven through the vent flange, a missing filter layer, or shingles that lifted off the vent cap. Water at the ridge is not a vent-clog problem, it’s an installation problem.
  • Filter layer packed with dust or blown insulation. Those little fiber filters catch everything. Once they’re packed, the vent is a solid plastic strip with a nice label on it.
  • Vent sections cracked, warped or flapping. Roofing plastic ages hard in southern Nevada sun. A vent that’s warped or flapping at the ridge means the fasteners gave or the section aged out.
Before & after

See the difference

Before - Recent ProjectBeforeAfter - Recent ProjectAfter
Recent Project
Before - Full RestorationBeforeAfter - Full RestorationAfter
Full Restoration
Before - Complete UpgradeBeforeAfter - Complete UpgradeAfter
Complete Upgrade

Replacement Cost & What’s Included

Our installs run $420 to $850 total for a standard single-family ridge line in Boulder City. Within that range, $9 to $16 per linear foot for the vent material and $40 to $75 per foot installed gets you the picture. The range depends on ridge length, whether it’s a shingle-over or low-profile vent style, and how much of that ridge has to be re-shingled after the vent goes on.

  • Remove old vent and inspect the deck – included
  • New Owens Corning-matched vent, filter layer, fasteners – included
  • Re-capping the ridge with matching shingles – included when the existing caps come off clean
  • New ridge cap shingles because the originals cracked – adds to the range
  • Attic inspection and soffit check – included, because a ridge vent without working soffits is wasted money

We hand you a written line-item price before anyone gets on the roof. No change orders mid-job. Every roofing job we do carries the 90-Day Done Right Promise in writing.

DIY or Call Us?

You can safely check a few things from the ground with binoculars: are the ridge shingles curled, are vent sections warped or missing, do you see daylight in the attic at the ridge. That’s the easy part.

Climbing the roof to replace vent sections is where it gets real. This is a ridge-line job at the highest point, the steepest angle, and the hottest surface of the house. Vent sections nail down under the shingle caps, and if the flange seal isn’t right, water finds it. We see owners in Boulder City get about 80 percent through a ridge vent swap and then face a leak they can’t track. If you’re over 55 or the pitch on your house is anything above a 6/12, stay off it. Bill and his crew will come out, and the estimate is free.

Call (844) 761-8186 to schedule a free estimate. A live person answers, day or night.

FAQs

Need Roofing help nationwide? Licensed & insured · free written estimates
Call (844) 761-8186
Local Service Coverage

Request a Free Estimate in Boulder City

Tell us what you need - Shepherd & Sons Roofing Boulder City responds fast. No obligation.

By submitting this form you agree to our Privacy Policy and consent to be contacted by phone, email or SMS about your request, including by local professionals who may handle it.

Prefer to text? Text Now
Call Now - 24/7 Dispatch