Owens Corning
Architectural shingles
Metal roofing
Tile roofing
GAF
Flat & low-slopeFree roof inspection with deck photos before we talk money - GAF and Owens Corning certified installation
Owens Corning Gutter Replacement: The Boulder City Owner’s Guide
Owens Corning-compatible gutter replacement in Boulder City typically runs $1,650 to $4,800 installed for a full run, and most single-run or sectional jobs can be scheduled within a day or two of your estimate. The reader who lands here usually found us the same way everyone does: a sagging run, an overflow stain on the stucco, or a downspout that pulls loose the second monsoon season hits. By the time the gutter has dropped an inch off the fascia, the fascia board behind it is often soft too. We measure the whole run, show you what the fasteners did to the wood, and put the number in writing before anyone touches the roof.

Which Owens Corning Models This Applies To
Owens Corning doesn’t sell a gutter system the way it sells shingles. What you’ll actually find on a Boulder City house is Owens Corning roof components (shingles, underlayment, sometimes the ice-and-water membrane) sitting above a gutter run made by a separate manufacturer. So “Owens Corning gutter replacement” in practice means matching a gutter length and profile to the roof edge Owens Corning decking and drip edge sit on. That’s a compatibility question, not a brand-logo question, and it’s the part most bids get wrong.
To identify what you’re replacing, get up on a ladder with a tape measure and check three things: the gutter’s top opening width (the common residential widths are 5-inch and 6-inch), the profile shape (K-style runs are near-universal on Owens Corning-shingled homes, but half-round shows up on older Boulder City builds), and the downspout size (2×3 or 3×4). Look at the drip edge where the shingle overhangs into the gutter. If that overhang is more than about an inch and a half, shingle replacement and gutter sizing both matter and a cheap aftermarket run will undershoot the flow. On the OEM-versus-aftermarket call: there’s no Owens Corning-branded gutter to chase, so a quality K-style section in the right dimension and gauge is the honest answer. The gauge matters more than the label. Thin 28-gauge aluminum will dimple under a hand; 26-gauge and heavier hold their shape.
Styles & brands we work with
- Architectural shingles
- Metal roofing
- Tile roofing
- GAF
- Owens Corning
- Flat & low-slope
Signs Your Owens Corning Gutter Replacement Is Failing
- Water staining on the fascia or stucco just under the gutter line. That usually means the gutter has separated from the fascia board and water is running behind it instead of into it. In Boulder City, the dry heat warps fascia and loosens fasteners faster than most owners expect.
- Gutter sagging between hangers. Hangers spaced too far apart, or hangers pulled from rotted wood, let the run dip. Once it dips, water pools and the seams open.
- Overflow at the corner during a rain. Usually a clogged or undersized downspout, but on a run older than about 20 years it can also be the gutter itself losing its slope. Las Vegas Valley heat bakes the sealant in seams until it gives.
- Pulling away from the roof edge, leaving a visible gap. That gap lets water miss the gutter entirely and soak the fascia and the wall behind it. Spring wind and summer sun both work on the same fasteners.
- Rust streaks or pinholes on steel gutter, or caulk lines that keep failing. Re-caulking a seam three times is a sign the metal is done. A failed seam under Owens Corning shingles above it is also a sign water has been tracking behind the roof edge.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Installed pricing for Boulder City gutter replacement depends mainly on run length, gutter gauge, downspout count, and whether we have to repair fascia behind the old run. Here’s the honest range:
- Single short run (under 40 feet), 5-inch K-style aluminum, one downspout: $1,650 to $2,400
- Typical full front or side run (40 to 80 feet), 5-inch or 6-inch: $2,400 to $3,600
- Full-perimeter replacement with multiple downspouts: $3,600 to $4,800
- Fascia repair where wood is soft, per linear foot: quoted separately, added to the estimate
What’s in the number: removal and haul-away of the old run, new hangers set into sound wood, sealed seams and corners, downspout and elbows, and a dumpster. What drives the range up: 6-inch gutter, heavier gauge, more corners, more downspouts, and any fascia replacement. We write the line items out, so you see what the metal, labor, and fascia work each cost. Every job carries our written 90-Day Done Right Promise. Call (844) 761-8186 for a free estimate and we’ll measure the run and show you what’s behind the old gutter before we quote.
DIY or Call Us?
Here’s the honest split. You can safely clean the gutter from the ground with a long-reach tool, eyeball the hanger spacing, and look for staining on the fascia from a ladder you’ve set on level ground with someone spotting you. That much is fine. What goes wrong on a DIY replacement is the roof edge itself: pulling old gutter off a Boulder City house often reveals soft fascia, and nailing into soft wood just delays the same failure a season. Working a ladder against a wall, wrestling 20-foot metal sections overhead, and getting the slope right so water actually drains toward the downspout are the jobs that cause injuries and callbacks. We use ladders every week and still take our time on a two-story run. If the gutter is more than a short single section, call us at (844) 761-8186 and let Bill’s crew handle the height. Free second opinion on any written estimate you’ve already got.

FAQs
A properly installed aluminum gutter run lasts 20 to 30 years here. The Boulder City sun and dry air are hard on the sealant in the seams and on the fascia wood the hangers bite into, so seam resealing and fastener checks every few years keep a run well past the 20-year mark. Heavier gauge runs last longer than thin 28-gauge.
Often, yes. A single pulled hanger, a clogged downspout, or one failed seam can be repaired for a fraction of replacement cost. We replace when the metal is rusted through, the run has lost its slope in multiple places, or the fascia behind it is soft. Call (844) 761-8186 and we’ll tell you which it is, honestly.
A single run is a one-day job. Full-perimeter work with fascia repair can run two to three days. We schedule it, pull no permits you don’t need, and we don’t leave a half-finished run overnight.
We match the gauge, profile width, and downspout size to your roof edge, then order the run from a local supplier. There’s no Owens Corning-branded gutter to source, so the matching is on gauge and dimensions, not a label. We install gutters and accessories alongside roofing from Owens Corning, GAF, and CertainTeed.
Shepherd & Sons Roofing Boulder City is an independent service provider and is not affiliated with Owens Corning. The name is used to describe the roofing and gutter systems we install and service.
Call (844) 761-8186 for a free estimate. A live person answers, day or night, and if it’s after a storm, Bill will come out and look at it with you. Standing offers: $40 off any repair over $200, and 10% off for seniors and veterans.
Written by the team at Shepherd & Sons Roofing Boulder City, serving Boulder City and nearby areas.