Metal roofing
Architectural shingles
Tile roofing
GAF
Owens Corning
Flat & low-slopeFree roof inspection with deck photos before we talk money - GAF and Owens Corning certified installation
IKO Specialty Roofing in Boulder City: What to Know First
We install and repair IKO specialty roofing in Boulder City as an independent IKO service provider. Most IKO specialty jobs here run one to three days on the roof once materials land, and low-slope work like TPO and modified bitumen often wraps faster. You’ll get a line-item written estimate before anyone touches the roof, a free second opinion on any bid you already have, and no trip charge inside the county.

This page is for Boulder City homeowners who own an IKO roof and need flat-roof or specialty work done right – not a hard sell. IKO covers a lot of ground, from Armourglass shingles to flat TPO and modified bitumen systems, and each one fails in its own way. Call (844) 761-8186 and a live person picks up.
How IKO Products Fail – and How We Fix Them
IKO makes solid products, but they don’t fail the way GAF or Owens Corning do, and knowing the difference saves you money. Here’s what we actually see on Boulder City roofs:
- IKO Armourglass and Cambridge shingles: thermal cycling at fasteners. Boulder City swings from hot afternoons to cool desert nights, and that swing loosens nails over the years. The shingle gets blamed, but the nailing is usually the culprit – too few, too high, or punched through the self-seal strip. We lift the tabs, check the pattern against the wind rating, and reset what’s loose rather than tear off a good field.
- IKO modified bitumen (Mop-Stick, Torch): seam and lap failures. Torch-applied caps separate where the granule surface wasn’t properly primed or the torch moved too fast. On a flat section this shows up as a soft spot or an edge lift after a monsoon. We cut out the failed lap, re-prime, and re-cap the seam so it bonds cold and stays put.
- IKO TPO: seam and fastener plate issues. Hot-air welded seams can fail where the installer didn’t hold the right temperature or the deck wasn’t clean. The symptom is a seam that looks fine until water gets under it. We probe every seam, weld repaired sections, and pressure-test before we call it done.
- IKO EPDM: adhesive and termination failures. On flat roofs the laps and terminations are where EPDM gives up first, especially when the adhesive was applied to a dirty or damp deck. Water wicks in at the edge behind the fascia. We re-bond the lap, fix the termination, and check the flashing line where it actually leaks.
- IKO built-up roofing: surface wear and ponding. Gravel-surfaced BUR can lose its mineral top over decades, and a Boulder City roof that ponded after a rare rainstorm will tell you where. We restore the surfacing, address the low spots that trap water, and inspect the deck underneath before we invest in coating a roof that can’t be saved.
That last point is the one owners can’t get off IKO’s own literature: a shingle or membrane usually isn’t defective – the install pattern or the deck is. We check both before we quote.
Styles & brands we work with
- Architectural shingles
- Metal roofing
- Tile roofing
- GAF
- Owens Corning
- Flat & low-slope
Our IKO Specialty Roofing Process
Here’s how an IKO specialty job runs from the first call to the last sweep:
- 1
Diagnostics. Bill or one of the crew gets on the roof, checks the deck and the flashing, and photographs what we find. We show you the deck photos before we talk money.
- 2
The parts call. For IKO systems we lean on OEM accessories where warranty safety matters, and quality aftermarket where it doesn’t. We’ll tell you which is which and why – no quiet substitutions.
- 3
The written estimate. Line-item, upfront, and free. A roof is measured in squares – ask any bidder how many they counted, and we’ll show you ours.
- 4
The work. Our techs have up to 30 years of experience, and the nailing pattern earns the wind rating, not the shingle wrapper. We build to the spec, not to what’s fastest.
- 5
The test. Every repaired seam, lap, and termination gets probed and water-tested before we pack up.
- 6
The guarantee. Every IKO job is backed by our written 90-Day Done Right Promise – if it’s not done right, we make it right.
See the difference
Before
After
Before
After
Before
AfterWhat IKO Specialty Roofing Costs in Boulder City
These are real ranges for common IKO scenarios in the Boulder City area. Your exact number depends on roof size, access, and how much deck we find damaged once we’re into it. The free estimate is where it gets precise.
| IKO Specialty Job | Typical Range |
|---|---|
| Localized modified bitumen or TPO seam repair | $300 – $800 |
| EPDM or TPO flat section repair | $500 – $1,500 |
| Full IKO TPO or EPDM low-slope re-roof | $4,000 – $9,500 |
| IKO built-up roofing restoration or coating | $1,800 – $4,500 |
| IKO shingle section replacement with deck repair | $900 – $3,000 |
What moves the price: deck condition, how many squares, whether existing flashing and terminations can be reused, and access on a sloped or low-slope section. A second story or a tight side yard adds labor. Call (844) 761-8186 to schedule your free estimate and get a number you can hold us to.
Why Boulder City Homeowners Call Shepherd & Sons Roofing Boulder City for IKO Work
Same address since 1996. Ask the storm chasers where theirs is. We’re locally owned and owner-operated, Bill’s name is on the license and on the truck, and a live person answers the phone 24/7 – not a call center, not voicemail. When a storm rolls through Boulder City and you need eyes on a flat section, someone picks up.
Our crew is background-checked, and Bill’s own sons are on the roof with him. Every IKO job carries the written 90-Day Done Right Promise, and one call brings Bill back. We also install GAF, Owens Corning, and CertainTeed, so if an IKO system isn’t the right fit for a section of your roof, we’ll tell you straight rather than force it.
FAQs
Not if the repair is done to IKO’s spec and the deck and flashing are handled correctly. Poor workmanship is what voids a manufacturer warranty – so we follow IKO’s installation requirements, keep the fasteners and accessories compatible, and document the work. That’s the whole point of doing it right.
Yes. We’re an independent IKO service provider and we source the IKO specialty products that fit your system. For time-sensitive repairs we’ll tell you upfront what’s OEM, what’s a quality aftermarket substitute, and what that means for your timeline.
It depends on the deck and how much of the membrane has failed. A single failed seam or a localized TPO weld is a repair. A low-slope roof with widespread seam failures or a soggy deck is usually a re-roof. We’ll show you the deck photos and give you an honest call, not the one that makes us the most money.
Most repairs are one to two days and most full IKO low-slope re-roofs are two to four days depending on squares and access. We give you a realistic schedule in the free estimate instead of promising a date we can’t hit.
Yes – every roofing job, IKO included, is backed by our written 90-Day Done Right Promise. If something isn’t right, one call brings Bill back to fix it.
Call (844) 761-8186 to schedule your free estimate. A live person answers 24/7, we offer a free second opinion on any written bid you already have, and there’s no trip charge inside our own county.
Written by the team at Shepherd & Sons Roofing Boulder City, serving Boulder City and nearby areas.