A Shepherd company - serving Boulder City, NV

IKO Flashing Replacement in Boulder City, NV

Architectural shinglesArchitectural shingles
Metal roofingMetal roofing
Tile roofingTile roofing
GAFGAF
Owens CorningOwens Corning
Flat & low-slopeFlat & low-slope
Every visit starts with

Free roof inspection with deck photos before we talk money - GAF and Owens Corning certified installation

We have financing partners for your new roof*On approved credit; ask us about your options
Get your free estimate

IKO Flashing Replacement: The Boulder City Owner’s Guide

We replace failed and failing flashing on IKO roofing systems throughout Boulder City, and most jobs run $385 to $720 installed for a full section, depending on length, pitch, and how much siding or stucco has to come back off. A simple pipe boot or small step-flashing run can land closer to $240. Most owners find out something’s wrong in one of two ways: a brown water stain creeps across a ceiling or wall, or they get up there in spring and see lifted, rusted, or curled flashing metal sitting against the IKO shingles. Flashing is the metal that seals the seams where your roof meets walls, chimneys, vents, and valleys, and on IKO installs it’s almost always the first thing to go before the shingles do.

Workers installing metal roofing panels on a residential home in Boulder City, NV

Call (844) 761-8186

Which IKO Models This Applies To

Flashing replacement isn’t tied to one IKO shingle line, and that’s the first thing to get straight. IKO Cambridge, Dynasty, and Armourglass all use the same basic metal flashing details – step flashing, counterflashing, valley metal, and pipe boots – so the part you need is matched to the roof configuration, not to the shingle brand. What IKO does specify is that flashing sits under the shingle course with a minimum 2-inch vertical leg and a nailing pattern that doesn’t leave the metal pinched against the shingle above it. When a crew gets that wrong, the flashing can’t move with temperature, and in Nevada’s swing from cold mornings to 100-degree afternoons, it works loose fast.

To identify what you have, check the underside of any shingle bundle wrapper if you still have one, or look for the IKO label on the inside of the attic on the sheathing. If the wrapper’s gone, measure the exposure – Cambridge runs about 5 5/8 inches to the weather. For the metal itself, we’re not going to sell you an “IKO flashing” the way you’d buy an IKO shingle, because IKO doesn’t make flashing. What we do is match a quality metal flashing to the IKO system – 26-gauge galvanized for most Boulder City roofs, or prefinished aluminum where the homeowner wants a color match. “OEM” here means the gauge, width, and bend match IKO’s install specs; aftermarket is fine as long as those specs are honored. We’re an independent outfit and not affiliated with IKO – we just know how their roofs are supposed to go together.

Explore

Styles & brands we work with

  • Architectural shingles
  • Metal roofing
  • Tile roofing
  • GAF
  • Owens Corning
  • Flat & low-slope

Signs Your IKO Flashing Replacement Is Failing

Here’s what we look for on a Boulder City roof, and what each sign actually means:

  • Rust streaks running down the shingles below a wall or vent. The flashing metal has rusted through or the galvanized coating has failed, usually on the south and west faces that take the most sun. Once rust starts, the metal’s sacrificial coating is gone and pitting follows.
  • Shingles curling or lifting right next to a wall, chimney, or valley. Water is getting behind the flashing and soaking the shingle edges, or the flashing was nailed tight and can’t expand. On IKO roofs we often find the flashing leg too short, so the shingle above it can’t overlap and seal.
  • Stains on a ceiling or the top of a wall inside. The flashing seal has opened at a seam, usually where it meets stucco or brick. Boulder City’s wind-driven rain pushes sideways into those gaps in a way that straight-down rain never does.
  • Caulk that’s cracked, chalky, or peeling along the flashing edge. The previous repair was a caulk-only patch, and caulk in southern Nevada sun has a realistic life of about two to three years before it fails again. This is the most common “repair” we’re called out to redo.
  • Visible gaps, loose nails, or wobbly pipe boots around plumbing vents. The rubber collar on a boot dries out and splits in the heat, or the metal base has pulled free. It’s a small part with a big leak potential, because it sits right where water funnels.
Before & after

See the difference

Before - Recent ProjectBeforeAfter - Recent ProjectAfter
Recent Project
Before - Full RestorationBeforeAfter - Full RestorationAfter
Full Restoration
Before - Complete UpgradeBeforeAfter - Complete UpgradeAfter
Complete Upgrade

Replacement Cost & What’s Included

On a typical Boulder City home, here’s the honest range for installed flashing replacement. We give a written line-item quote before anything gets torn open, and the number doesn’t change at the door.

Job Typical Installed Range
Single pipe boot / vent collar $240 – $340
Step flashing at one wall or dormer $385 – $560
Chimney flashing and counterflashing $520 – $720
Valley metal, per linear run $420 – $680

What drives the range is length, roof pitch, and how much stucco or siding has to be cut and patched. What’s included: new metal matched to your IKO install specs, removal and proper disposal of the old flashing, new underlayment where the old was compromised, and re-sealing at every penetration. Every job carries our written 90-Day Done Right Promise – if it leaks, one call brings us back. Parts-plus-labor is transparent on the quote; you see the metal cost and the labor separately.

Workers installing metal roofing panels on a residential home in Boulder City, NV

DIY or Call Us?

You can safely check flashing from the ground with binoculars, or on a low roof you can reach with a ladder. Look for rust, gaps, loose nails, and cracked caulk. Checking is fine. Getting up on a steep pitch to replace it is a different story – we’re talking about working at height on a slope, prying up shingle courses to weave new metal, and lifting the roof edge anywhere from a dozen to forty times per run. An owner nailing a new flashing leg flush against the shingle above it, without a gap for movement, will watch it buckle loose by the next hot afternoon. And if a shingle tears or the nailing pattern is wrong, the leak moves and the wind rating goes with it. This is one of those jobs where the wrong repair can quietly make things worse.

The best move is honestly two things: eyeball it from the ground, then let someone with a license and a ladder come out. The team has up to 30 years of experience with IKO roofs. Call (844) 761-8186 for a free second opinion on any written estimate – we’ll show you the deck photos before we talk money.

FAQs

How long does IKO roof flashing last in Boulder City? A properly installed galvanized flashing on a Boulder City roof should give 15 to 25 years, with prefinished aluminum running a bit longer. Heat, sun exposure on the south and west faces, and wind-driven rain all shorten that. If you see rust at year 10, the metal’s coating failed early.

Can a failing IKO flashing be repaired instead of replaced? Sometimes, and we’ll tell you honestly which it is. A cracked caulk line or a single loose nail can be repaired. But rust-through, a split pipe boot, or a flashing leg that was installed wrong won’t keep out water, no matter how much caulk goes over it. Call (844) 761-8186 for an exact quote – estimates are free.

How long does a flashing swap take? A pipe boot is a couple of hours. Step flashing at one wall or a chimney runs most of a day because the shingle courses have to come up and go back down clean. Valley metal is a longer job. We schedule it as a planned repair, not an emergency, and you’ll know the timeline before we start.

How do you source the flashing part? We don’t stock parts on a truck and we won’t tell you we do. We measure at the site, then order the correct gauge and bend – 26-gauge galvanized or prefinished aluminum – from a local supplier matched to your IKO install specs. We also service GAF, Owens Corning, and CertainTeed roofing, so if you’re not sure which system you have, we can figure it out on site.

Ready to get that flashing sorted before the next rain? Call (844) 761-8186 for a free estimate. Live person answers, 24/7 – not a call center, not a voicemail. No trip charge inside our county, a Free Second Opinion on any written estimate, and $40 off any repair over $200. Ask anyone on your street – the name on the truck is the name on the license.

Written by the team at Shepherd & Sons Roofing Boulder City, serving Boulder City and nearby areas.

Need Roofing help nationwide? Licensed & insured · free written estimates
Call (844) 761-8186
Local Service Coverage

Request a Free Estimate in Boulder City

Tell us what you need - Shepherd & Sons Roofing Boulder City responds fast. No obligation.

By submitting this form you agree to our Privacy Policy and consent to be contacted by phone, email or SMS about your request, including by local professionals who may handle it.

Prefer to text? Text Now
Call Now - 24/7 Dispatch