Architectural shingles
Metal roofing
Tile roofing
GAF
Owens Corning
Flat & low-slopeFree roof inspection with deck photos before we talk money - GAF and Owens Corning certified installation
IKO Gutter Replacement: The Boulder City Owner’s Guide
We install IKO-compatible gutter replacement throughout Boulder City, and most full runs land between $8 and $22 per linear foot installed – so a typical 120-foot house runs roughly $1,200 to $2,400, while a longer two-story run with downspouts and fascia work reaches $3,000 to $4,500. We can often get a crew out the same week you call, and if a run is failing hard before a monsoon forecast, we’ll tell you honestly whether it can wait. This isn’t a same-day emergency service, so plan on a scheduled visit.

Most Boulder City owners discover the problem the same way. They’re up on a ladder clearing pine needles after a wind event, and the gutter channel is sagging away from the fascia at a hanger or pulling loose at a seam. Or they notice a rust-colored streak down the stucco and follow it back to a joint that let go. The IKO name on their fascia or drip edge made them think the whole system was one brand, and they call us expecting a simple swap. It’s usually a bit more than that, but it’s never a guessing game once we’re on the roof looking at it.
Which IKO Models This Applies To
IKO makes shingles first and foremost, and it makes drip edge and some gutter-adjacent trim products alongside them. When a homeowner tells us “I have IKO gutters,” what we usually find on the roof is one of a few things: IKO drip edge along the rake and eave, or a gutter run installed to match an IKO shingle package when the roof was last replaced. IKO’s residential lines include the Cambridge, Dynasty, and Nordic shingle families, and each one carries a different profile and thickness – which matters because the drip edge and hanger spacing should match the shingle overhang, not the other way around.
Here’s how to identify what you’re actually looking at. Get up close (safely, from the ground with binoculars if you have to) and look for the IKO logo stamped on the drip edge flange or printed on the shingle wrapper left in the attic or garage. Measure the gutter channel width – most residential runs are 5-inch or 6-inch K-style, and that measurement is what we order against, not the brand name. Check the hanger spacing and the type of hanger; strap hangers, hidden hangers, and spike-and-ferrule all take different replacement parts. If the shingle wrapper says IKO and the gutter doesn’t carry a visible mark, that’s normal – IKO doesn’t brand most of its gutter accessories, and we match by measurement and profile rather than by label.
On the OEM-versus-aftermarket question, here’s the straight answer: for gutter replacement, there is no “IKO OEM gutter part” the way there’s an OEM part for a car. Gutter is gutter, and the brand on the shingle doesn’t lock you into a brand on the channel. What matters is the gauge of the aluminum, the hanger type, and whether the drip edge and shingle overhang are matched correctly. We set quality aftermarket gutter that meets or exceeds the profile of what’s on your roof, and if the drip edge is IKO and still serviceable, we leave it. If it’s failing, we replace it with a matched profile so the shingle edge still sheds correctly.
Styles & brands we work with
- Architectural shingles
- Metal roofing
- Tile roofing
- GAF
- Owens Corning
- Flat & low-slope
Signs Your IKO Gutter Replacement Is Failing
Five symptoms we see over and over on Boulder City roofs, and what each one is telling you:
- Sagging between hangers. The hanger spacing was too wide for the gauge of aluminum, or the hangers pulled out of rotted fascia. Once one section sags, water pools there instead of running to the downspout, and the sag spreads.
- Rust-colored streaks on stucco or siding. A seam or end cap has let go, and water is running behind the gutter instead of through it. In Boulder City’s dry climate, this often shows up suddenly after the first rain following a long dry spell, when the seam seal has dried and cracked.
- Water sheeting over the front edge during rain. The gutter is pitched wrong, undersized for the roof area, or clogged at the downspout outlet. A 5-inch channel that was fine for a small roof can overflow when the roof was expanded or re-shingled with a heavier profile.
- Gutter pulling away at the fascia. The fascia board behind the gutter has softened from long-term water exposure. This is the one that surprises owners, because the gutter looks fine until you push on it and the whole run moves. Replacing gutter without addressing the fascia is money thrown away.
- Downspouts that dump right at the foundation. Not a failure of the gutter itself, but a failure of the system, and common on older Boulder City homes that were built before splash blocks were standard. It’s why we look at the whole run, not just the channel.
One reality worth naming: aluminum gutter in southern Nevada typically holds up 20 to 25 years before the seams and hangers start to give. The sun and the dry-then-wet cycling are hard on sealant. If your run is past that mark and failing in more than one spot, replacement is usually the better call than chasing repairs.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Installed gutter replacement in Boulder City runs roughly $8 to $22 per linear foot, depending on gauge, size, and how much fascia repair is involved. Here’s what the range looks like in line-item form:

| Item | Installed range |
|---|---|
| 5-inch K-style aluminum, per linear foot | $8-$14 |
| 6-inch K-style aluminum, per linear foot | $11-$18 |
| Downspouts, per linear foot | $6-$12 |
| Hanger replacement / re-spacing | $4-$9 per hanger |
| Fascia board repair (where soft) | $12-$30 per linear foot |
| Drip edge replacement, matched profile | $3-$7 per linear foot |
What drives the top of the range: two-story access, long runs with multiple inside corners, and fascia that needs replacing before new gutter can go on. We quote line-item and in writing, we don’t do change orders mid-job, and the work is backed by our written 90-Day Done Right Promise. If something isn’t right, one call brings Bill back out.
DIY or Call Us?
Here’s what’s safe to check yourself: from the ground, look for sag, separation at the fascia, and streaks on the wall. From a stable ladder at the gutter line (never on the roof in wind, never on a wet roof), you can clear debris by hand and check that water flows toward the downspout. That’s it. What turns DIY into a bad afternoon is climbing onto a pitched roof to pull a gutter run, cutting and fitting new hangers into soft fascia, or re-pitching a channel – that’s where homeowners get hurt and where a half-done job makes the water problem worse. Roof work at height in Boulder City heat is a real risk, and it’s not worth it to save a few hundred dollars on a job that should last two decades.
If you’re not sure what you’re looking at, call us at (844) 761-8186. We’ll come out, show you what’s failing, and give you a free written estimate. No trip charge inside our own county, and we’ll give you a free second opinion on any written estimate you’ve already got.
FAQs
Twenty to twenty-five years for quality aluminum in our climate, provided the hangers are spaced correctly and the fascia behind it stays dry. The sun and dry-then-wet cycling age the seam sealant faster than the metal itself, so seam and hanger maintenance is what determines whether you get 15 years or 25.
Sometimes, yes – a single loose hanger, a resealed seam, or a re-pitched section is a legit repair. If more than a couple of spots are failing or the fascia is soft, replacement is the better use of your money. We’ll tell you which one you’re looking at rather than push the bigger job.
A typical single-story run is a one-day job; two-story homes with multiple corners and fascia repair usually run two days. We schedule it, show up when we say, and clean up the site before we leave.
We match by measurement and profile – channel width, gauge, hanger type – and order from suppliers we’ve used for years. We don’t carry gutter stock on a truck and we’re not an IKO dealer; we’re an independent roofing and gutter contractor. Shepherd & Sons installs products from GAF, CertainTeed, Owens Corning, and IKO across our roofing work, and gutter to match whatever’s on your roof.
If your IKO-era gutter is failing, we’ll come look at it, show you the deck and the fascia, and give you a straight number. Call (844) 761-8186 for a free estimate – a live person answers, day or night. Same address since 1996, and the name on the truck is the name on the license.
Written by the team at Shepherd & Sons Roofing Boulder City, serving Boulder City and nearby areas.