Architectural shingles
Metal roofing
Tile roofing
GAF
Owens Corning
Flat & low-slopeFree roof inspection with deck photos before we talk money - GAF and Owens Corning certified installation
Tamko Flashing Replacement: The Boulder City Owner’s Guide
We replace failed Tamko-compatible roof flashing in Boulder City for installed prices that typically land between $285 and $650, depending on pitch, length of the run, and whether the old sealant has to be ground off first. It’s a one-day job in most cases, and we schedule it after a free look at the roof. Most owners find out something’s wrong when a brown water ring shows up on a ceiling board after a monsoon push, or when they climb up and see the sealant pulled away from the wall and the metal lifting at a corner.

Which Tamko Models This Applies To
Tamko flashing shows up across their shingle lines, so this isn’t a one-model fit. We run into it on Heritage and Heritage Pro architectural shingles, on the Lamarite and Titan XT lines, and on older Tamko three-tab work that predates their current packaging. The flashing itself is usually the roll or formed metal sitting at a wall, a chimney chase, a valley, or a skylight curb, and its job is to shed water out from under the shingle course rather than letting it wick back into the deck.
Matching the right part comes down to measurements, not model numbers. Measure the exposed face height, the length of the run, and the gauge of the metal (0.019 inch and 0.024 inch are the common roofing gauges, and a heavy run in a windy spot wants the thicker number). Then match the leg that slides under the shingle course; if the old flashing tucked too tight against the deck, water backdams and lifts shingles. Tamko-labeled flashing is available through roofing suppliers, but plenty of jobs are done with quality aftermarket coil in matching color. On a Boulder City roof, what matters more than the label is the gauge, the bend quality, and how it’s fastened, not whose stamp is on it. We also work with GAF, Owens Corning, and CertainTeed flashing if your roof is a mix of brands.
Styles & brands we work with
- Architectural shingles
- Metal roofing
- Tile roofing
- GAF
- Owens Corning
- Flat & low-slope
Signs Your Tamko Flashing Replacement Is Failing
- Sealant that’s pulled away from the wall or chimney chase. The mastic dries out in Boulder City’s low humidity and high summer heat, cracks at the joint, and stops shedding water. That seam is the first thing we look at on a roof.
- Rust streaks running down from under a course. Bare or poorly coated metal starts to pit, and once it’s pitted, water gets a path around the flashing instead of over it. You’ll usually see the orange stain before you see the hole.
- Shingles lifting or curling at a wall or valley edge. That’s the flashing pushing back against the shingle course because it was set too high or too tight. Left alone, the wind grab picks up there first.
- Ceiling stains or damp sheathing after a desert downpour. Boulder City gets sudden rain that has no time to slope off, and a flashing gap lets it in fast. A ceiling ring on the south slope is a strong sign this part is the culprit.
- Daylight or gaps you can see through from under the eave or from inside the attic. Any daylight at the wall line means the flashing isn’t sealed. That’s a gap, not a gasket issue.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Most Boulder City flashing replacements on a Tamko roof run between $285 and $650 installed. Here’s what drives the number:
- Run length and height. A short wall flashing at a side-yard detail is at the low end. A chimney chase or a long valley run with a steep pitch pushes it up.
- Gauge and material. Thicker coil, a colored finish out of the same family as the shingle, and formed pieces cost more than standard roll.
- Old-sealant removal. If we have to grind and clean the deck before the new piece goes on, that’s real time on a ladder.
- Shingle reset. Tucking new flashing under existing courses means pulling and re-setting a run of shingles, so pitch and course condition affect the labor.
The price we give you is the price on the job. We don’t quote one number on the phone and a different one at the door, and each job is backed by our 90-Day Done Right Promise in writing. If it’s not right, we come back and make it right. Free second opinion on any written estimate, and no trip charge inside our own county.

DIY or Call Us?
A quick check is fine to do yourself. From the ground with binoculars, or safely up on a low-pitch wall detail, look for the rust streaks, the lifted shingle edges, and any daylight gap you can spot without walking the roof.
What gets people in trouble is the actual swap. Roofing work puts you on a ladder and a pitch, and on a hot Boulder City afternoon a misstep is serious. Once you start pulling shingles to tuck the new flashing under the course, you’re affecting the water-shedding layering and the nail pattern, and if the metal gauge is wrong you’ve traded one leak for another. We’ve seen plenty of flashing jobs that got redone because someone set the metal flat to the deck and skipped the shingle overlap. That’s what the crew and I fix. If your roof’s showing any of the signs above, call (844) 761-8186 for a free look before the next rain finds it.
FAQs
Quality flashing with a solid coated finish runs 15 to 25 years in our climate, but the sealant at a wall or chase can fail in 5 to 10 because the desert sun and low humidity crack it. The metal often outlives the sealant by a wide margin, which is why a flashing replacement on a 20-year-old Boulder City roof is common. If you’re seeing the first signs, call (844) 761-8186 for a free estimate.
Sometimes a repair is enough, if the metal is intact and only the sealant has failed at the wall line. When the metal is pitted, dented, or set too tight, spot repair just hides the problem. We’ll tell you which one you’ve got. Call (844) 761-8186, and we’ll give it a real look and a straight answer.
Most flashing replacements are done in a day. A short wall run is a few hours; a chimney chase or a long valley with shingle reset takes longer. We don’t leave the roof open overnight. Call (844) 761-8186 to get on the schedule and get a firm estimate.
We source the flashing through roofing suppliers based on the gauge, the measured run, and the color match to your existing shingles, which means we match the spec rather than carrying a stack on the truck and hoping it fits. That’s why the measurements come first. Call (844) 761-8186 for a free estimate and we’ll walk the roof together.
Written by the team at Shepherd & Sons Roofing Boulder City, serving Boulder City and nearby areas.