Architectural shingles
Metal roofing
Tile roofing
GAF
Owens Corning
Flat & low-slopeFree roof inspection with deck photos before we talk money - GAF and Owens Corning certified installation
Boral Flashing Replacement: The Boulder City Owner’s Guide
Boral-compatible flashing replacement in Boulder City typically runs $290 to $640 installed for a standard run, and most jobs are finished in a single visit. We match the flashing to your Boral product line, pull the right profile, and seal it so the wall-to-roof joint does what it was supposed to do the first time. Most Boulder City owners find out they need this work the same way: a brown water stain creeps across the ceiling after a monsoon, or they spot rust bleeding down the stucco under a roofline. Sometimes it’s the flashing that’s plainly lifted away from the wall, and the gap shows daylight. Either way, the flashing stopped shedding water before the roof did.

Which Boral Models This Applies To
Boral makes both roofing tile and siding products, and the flashing that matters depends on which one you’ve got. On the tile side, the common Boulder City candidates are Boral’s flat and low-profile concrete tile lines, including the Saxony and Barcelona profiles, along with the steel-roofing panels Boral distributes. On the siding side, it’s the Boral composite and fiber-cement lap and trim boards, where the flashing is really the head and sill flashing at penetrations and wall terminations.
To identify what you have, look at the tile tag or the stamp on the back of the tile, or the label on the siding bundle, not the color. Color tells you nothing about which flashing profile fits. Measure the tile’s width and thickness at the course, and note whether the profile is flat or barrel. That measurement is what selects the part.
OEM versus aftermarket is the real decision here. Boral-branded flashing carries the exact fit, but a quality aftermarket equivalent in the same gauge and profile does the same job and often saves money on a small run. We’re an independent contractor and not affiliated with Boral, so we’ll tell you honestly which one your job needs. What we won’t do is claim we stock parts or carry them on a truck. We source what your roof calls for.
Styles & brands we work with
- Architectural shingles
- Metal roofing
- Tile roofing
- GAF
- Owens Corning
- Flat & low-slope
Signs Your Boral Flashing Replacement Is Failing
- Rust streaks on the stucco or siding below a roofline. The flashing coating has broken down and the steel underneath is corroding. In Boulder City’s dry heat, that coating fails faster than most owners expect because the flashing expands and contracts hard every summer day.
- Water stains on the ceiling or along the top of a wall after rain. The flashing has pulled away or the sealant at the joint has cracked. That’s water finding the gap the flashing used to cover.
- Visible gaps or lifted edges where the flashing meets the wall or the first tile course. Fasteners have backed out or the metal has warped. Once it’s lifted, wind-driven rain goes straight in.
- Granule or sealant debris collecting in the gutter below the flashing. The sealant is breaking down before it fails outright. Catch it here and the job is smaller.
- Daylight or a draft at the joint from inside the attic. The flashing has separated far enough to open a path for water and air. This one usually means the leak is already happening.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Installed flashing replacement for a Boral roof or wall in Boulder City lands around $290 to $640 for a standard run. The range moves with three things: how many linear feet you’re covering, the gauge and profile of the metal, and how much old flashing and sealant has to come out before anything new goes on. A short chimney or wall run sits at the low end. A long valley or a run with damaged underlayment underneath climbs toward the top.
We break the quote into parts and labor so you can see what the metal costs and what the install costs. No change orders, no surprise add-ons. Every roofing job carries our written 90-Day Done Right Promise, and if it’s not right, one call brings Bill back. Take $40 off any repair over $200, and your senior or veteran discount applies on top. The free second opinion on any written estimate is there if you want a number to compare against.

DIY or Call Us?
Here’s the honest split. You can safely walk your roofline from the ground, check for rust streaks, look at the flashing joint with binoculars, and check inside the attic for daylight or water stains. That’s a real diagnosis and it’s free.
What you shouldn’t do is get up on a Boulder City roof and pry off flashing to reseal it yourself. Roof work means heights, and flashed joints mean lifting the tile or siding course above the metal, which is where homeowners break tiles, tear underlayment, and turn a $400 flashing job into a $2,000 repair. The sealant has to go on under the right conditions or it fails inside a season. This isn’t a part to learn on. Call us at (844) 761-8186 and we’ll come out, look at the deck, and give you a straight number.
FAQs
Quality metal flashing with a sound coating lasts 15 to 25 years in southern Nevada, but the sealant at the joint lasts closer to 5 to 8 years and is usually what fails first. Boulder City’s summer heat is the culprit: the metal expands hard in the afternoon and contracts overnight, and that cycle wears the sealant out before the metal gives up. Call (844) 761-8186 for an exact quote. Estimates are free.
Sometimes, yes. If the metal is sound and only the sealant has failed, a reseal is a real repair and it’s cheaper. If the flashing is rusted through, warped, or has pulled loose, replacement is the only fix that holds. We’ll tell you which one you’re looking at before we quote either.
A standard flashing run on a Boral roof or wall is usually a single-visit job, finished in a few hours once we’re on site. Longer runs or jobs that need the course above the flashing lifted take most of a day. Bill will give you the realistic window before anyone touches your roof.
We match the flashing to your specific Boral profile by measuring the tile or siding at the course, then order the OEM or a quality aftermarket equivalent in the correct gauge. We don’t stock Boral parts and we don’t carry them on the truck, so the lead time depends on what your roof needs. That’s why we measure first and quote after.
We also handle GAF, Owens Corning, and CertainTeed products if your roof has a mix of materials. Same address, same name on the truck. Call us at (844) 761-8186 to schedule your free estimate.
Written by the team at Shepherd & Sons Roofing Boulder City, serving Boulder City and nearby areas.