Architectural shingles
Metal roofing
Tile roofing
GAF
Owens Corning
Flat & low-slopeFree roof inspection with deck photos before we talk money - GAF and Owens Corning certified installation
Boral Gutter Replacement: The Boulder City Owner’s Guide
Boral gutter replacement in Boulder City runs $1,400 – $3,800 for most single-story homes, and we can usually get out to look at it the same day you call. That price covers tear-off of the old run, Boral-compatible seamless aluminum formed on site, hangers, end caps, downspout reconnection and cleanup. A failed gutter rarely announces itself. You notice it on a windy Tuesday when a 40 mph gust off the McCullough Range peels a section off the fascia, or after a monsoon dump when water is sheeting over the back patio and pooling against the block wall instead of leaving through the downspout. Sometimes it’s quieter: paint bubbling under the run, or hard-water streaks reappearing every few weeks where the seams keep opening.

Which Boral Models This Applies To
Boral’s US gutter line is mostly formed aluminum in 5-inch and 6-inch K-style profiles, plus half-round and specialty shapes. The old “Boral Western” fascia and trim line, common on Las Vegas-area homes built from the late 1980s through the mid-2000s, is a separate animal and often gets confused with the gutter side. If your home has that fascia trim, pull the piece off and look for the profile stamp before ordering anything, because the replacement trim is not the same extrusion as the gutter.
The first check on a 5-inch Boral gutter: measure the actual formed profile width with a tape. Boral has run more than one 5-inch die over the years, and the front lip depth has varied by a sixteenth or so, which matters when you’re buying hangers or matching a run into an existing one. A hidden hanger sold as “universal 5-inch” will not always clip a Boral profile cleanly.
On the OEM-versus-aftermarket question: Boral-branded accessories (end caps, outlets, inside and outside corners) pop up at the local supply houses less often than they used to. A quality aftermarket 5-inch K-style piece from a maker like Amerimax or Spectra Metals can match a standard Boral profile closely enough that the run looks continuous from the ground. The honest answer is that the profile has to match, not the label. Bring a six-inch cutoff of the old gutter with you when you go to the yard.
Styles & brands we work with
- Architectural shingles
- Metal roofing
- Tile roofing
- GAF
- Owens Corning
- Flat & low-slope
Signs Your Boral Gutter Replacement Is Failing
- Seams opening at corners and outlets. The sealant behind a Boral corner or outlet dries and shrinks faster in Boulder City’s dry heat than the extrusion itself. If you’re resealing the same joint every spring, the piece is likely distorted out of shape and a fresh tube won’t fix it.
- Sagging between hangers. Hangers spaced wider than 24 inches on center cannot hold up to a monsoon rain dump or a wet snow load on the uphill side of a Boulder City roof. Once the gutter sags, water pools at the low spot and back-slopes into the fascia board.
- Streaking under the gutter. That white mineral crust on the stucco comes from hard water and high desert dust, not from roof shingle granules. If it’s reappearing along the same line, the gutter is overflowing on the back edge because of a slope or debris issue, not a paint issue.
- Loose nails at the fascia. Older Boral gutter was nailed to the fascia through a front flange on the tall wood. In Boulder City sun, the fascia dries and cracks and the nailing loses bite. Check by pushing on the bottom of the gutter channel from the ground.
- Downspout pulling from the outlet. When the run expands and contracts with heat, it stretches the outlet and downspout until they separate. That’s often the first place an owner sees water against the wall.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Installed gutter replacement in Boulder City works out to roughly $14 – $30 per linear foot for 5-inch K-style seamless aluminum, and $20 – $38 per linear foot for 6-inch. Most single-story homes land between $1,400 and $3,800 per run. That range covers tear-off and haul-away, new hangers on 24-inch centers, formed seamless sections, end caps, outlets, and reconnection to existing downspouts.
What moves the number up or down:
- Roof pitch and access. Two-story work or steep pitches cost more per foot.
- Linear footage, obviously. Have the bidder count feet in front of you and write it on the estimate.
- New downspouts. If your existing ones are intact, you save.
- Fascia repair. If the wood has rotted behind the gutter, it gets fixed, not covered.
You get the price in writing, line-item, before anyone touches your roof. Every job is backed by our written 90-Day Done Right Promise, and a free second opinion on any written estimate means you can compare apples to apples.
DIY or Call Us?
There’s a safe middle ground and a not-safe line, and it’s worth being honest about both. Safe from the ground: walk the perimeter with binoculars, look for sags and streaks, poke the bottom of the gutter channel with a long pole to feel how solid the hangers are, and flush the downspouts with a garden hose. That’s all useful and you should do it.

What we don’t recommend: climbing a ladder to dismount a full gutter run yourself, especially at two-story height or on a cloudy February day when the aluminum is cold and slick. We’ve seen homeowners get hurt doing exactly this. Gutter work looks simple from the driveway. It isn’t, and it’s not the place to save a couple hundred dollars.
The other reason to call: matching a Boral profile, hangers and outlets with a compatible die takes experience, and it’s what our technicians have up to 30 years of doing. We also install GAF, Owens Corning and CertainTeed systems when the job calls for a full rework. Call (844) 761-8186 and we’ll get someone out there.
FAQs
A properly installed Boral-compatible aluminum gutter will run 20 – 25 years in Boulder City’s climate, sometimes longer if the hangers are spaced right and downspouts aren’t allowed to plug. What shortens that lifespan isn’t the metal, it’s the sun-facing slopes with no shade and the wind-driven dust that settles into the channel and backs water up.
Sometimes, yes. If one section has pulled loose from the fascia or a single sealant joint has opened, a repair makes sense and usually runs $150 – $400. If the run is more than 15 years old and showing sag between multiple hangers, replacement costs less over time than chasing leaks every season. We’ll tell you which one you’re looking at after we see it.
Most single-run replacements on a Boulder City home are done in a single day. A full-perimeter job on a larger one-story house takes two. We don’t quote install time by phone until we’ve walked the roof and seen the fascia, because that’s where the surprises live.
We match the profile to the existing run, then source from local supply houses we’ve worked with since 1996 and from manufacturers we trust for the fit. If the exact Boral die isn’t available, we’ll tell you that straight and show you the aftermarket piece we’d use instead, side by side. Shepherd & Sons Roofing Boulder City is an independent service provider and not affiliated with Boral.
Then we’ve walked the job and found something the phone couldn’t tell us, like rotted fascia or three hangers that were barely holding. You get the second number in writing before anyone touches the roof, and you’re free to say no. Same address since 1996. Ask the storm chasers where theirs is.
Call (844) 761-8186 for a free estimate. A live person answers, day or night, and no trip charge inside our own county. Same name on the truck, same name on the license.
Written by the team at Shepherd & Sons Roofing Boulder City, serving Boulder City and nearby areas.