Architectural shingles
Metal roofing
Tile roofing
GAF
Owens Corning
Flat & low-slopeFree roof inspection with deck photos before we talk money - GAF and Owens Corning certified installation
CertainTeed Flashing Replacement: The Boulder City Owner’s Guide
Flashing replacement on a CertainTeed roof runs roughly $300 to $900 installed in Boulder City, with most single-run jobs at the lower end and chimney or valley work at the top. We schedule these in Boulder City inside a normal work week, and a straight run is usually a one-visit job. Owners almost always find the failure the same way: a brown water stain on a ceiling near a chimney, wall, or valley, or a rusted line above the siding that shows up after a hard spring wind. You go up to look, and the metal edge that should tuck under the shingle is bent, lifting, or gone to rust.

Which CertainTeed Models This Applies To
CertainTeed flashing isn’t a single product. It’s a mix of metal edge, valley metal, step flashing, and counterflashing that comes alongside their shingle and roofing lines, and the correct replacement depends on your roof assembly, not just the shingle wrapper. Knowing which CertainTeed roof you have helps. CertainTeed shingle lines run through the Landmark, Independence, Northgate, and Presidential families, with color and profile matching sheet metal and accessory flashing made for the same job. Painted aluminum flashing made for CertainTeed shingle profiles matches trim and fascia better than generic galvanized from the hardware store. The catch: metal edge extrusions vary in face height and drip lip depth by manufacturer, so a stock piece at the big box may not seat exactly where your old profile sat.
How to identify what you need:
- Check the label on the original shingle wrapper stored in your garage or attic, or ask your builder’s paperwork for the CertainTeed line and color.
- Measure the metal edge face height and drip lip depth with a tape measure. Those two numbers tell us what will seat cleanly.
- Note whether your roof uses painted aluminum, galvanized steel, or copper, because replacement metal should match so it weathers and paints the same.
On the OEM-versus-aftermarket question: factory CertainTeed accessories match color and profile exactly. A quality aftermarket metal edge in the same face height and finish installs just as well and costs less, provided it’s painted aluminum rated for our sun. We’ll tell you which is the better buy for your roof instead of upselling the label. Shepherd & Sons Roofing Boulder City is an independent roofing company, not affiliated with CertainTeed, so our only stake is what lasts on your roof. We also replace flashing on GAF and Owens Corning roofs.
Styles & brands we work with
- Architectural shingles
- Metal roofing
- Tile roofing
- GAF
- Owens Corning
- Flat & low-slope
Signs Your CertainTeed Flashing Replacement Is Failing
Flashing fails before the shingles around it do, and it fails in a handful of predictable ways. Here’s what to look for on your CertainTeed roof:
- Rust streaks or chalky white stains on the metal edge. Painted aluminum that loses its coating in our desert sun starts to oxidize and stain the fascia below. Once the paint chalks off, water has a path under the paint and into the lap.
- Drip edge pulling away from the fascia. Wind-driven rain and expanding wood push the edge out of place. Once the metal edge lifts, water sneaks behind the fascia board and rots it from the inside out.
- Lifted or curled step flashing at a sidewall or chimney. Step flashing lifts where it was nailed too tight, and once it lifts, the shingles above it can’t shed water past the wall. That’s the classic stain-on-the-ceiling-beside-the-chimney call.
- Caulk or sealant cracking along a counterflashing line. Sealant is a temporary patch, not flashing. When it dries and cracks in our summer heat, water gets behind the counterflashing and runs down the masonry.
- Granule loss and lifting shingles right at a valley or wall. Water backing up under the flashing edge lifts the shingles above it. By the time you see granule loss there, the flashing has been leaking for a while.
Our technicians have up to 30 years of experience reading these signs, and we’ll show you the photos of what we find before we talk price.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Typical installed prices in Boulder City:

| Job | Installed Range |
|---|---|
| Drip edge, single straight run | $300 – $500 |
| Step flashing at a sidewall or chimney | $450 – $700 |
| Valley flashing, one valley | $550 – $900 |
What moves the number up or down: how many linear feet of flashing you actually need, how high the roof is and whether we can walk it safely, how much the old metal has to be cut out, and whether the shingles above the flashing have to be lifted and reset. When we lift shingles, we reset them or replace what’s too brittle to reuse. Parts and labor are broken out separately on the estimate so you can see what the metal costs versus the work. Every flashing job carries the written 90-Day Done Right Promise: if it’s not done right, one call brings us back to make it right. You’ll get a free second opinion on any other written estimate, and there’s no trip charge inside our own county.
DIY or Call Us?
An owner can safely check a few things: look up at the metal edge from the ground with binoculars, check attic rafters near the chimney and walls for water staining after a rain, and note where you see rust or lifted metal. What an owner should not do is get up on the roof to pry off and re-seat flashing themselves. Two reasons. First, a good share of our valley and wall calls are roofs steep enough that one wrong step is a long fall, and flashing work means standing right at the edge. Second, the flashing only works if it’s overlapped and tucked in the right order under the shingles, and getting the lap or the nailing wrong means the leak comes back next storm, sometimes worse. That’s where DIY goes wrong, and it’s not worth the risk to save a few hundred dollars. If you’re not sure whether your flashing is failing or just lost its paint, call us at (844) 761-8186. We’ll tell you straight.
FAQs
Painted aluminum flashing on a Boulder City roof typically holds up 15 to 25 years before the coating chalks off and it starts to oxidize, though our high-desert sun and hard spring winds push the constant-exposure runs toward the shorter end. Galvanized steel runs longer, but once the zinc coating is gone it rusts fast. Call (844) 761-8186 for a look at yours; estimates are free.
Sometimes, yes. If the metal is sound and just a step flashing or a sealant line has failed at one spot, a spot repair can get you through a season. But if the paint is gone, the metal is bent, or rust has started at a lap, patching it is money you’ll spend again next year. We’ll tell you which category you’re in. Call (844) 761-8186 for a free estimate.
A single straight run of drip edge is usually a few hours, and step flashing at a chimney or a single valley is typically done in one day, weather permitting. Jobs that involve lifting more shingles take longer. We’ll give you a realistic window when we see the roof. Call (844) 761-8186 to schedule your free estimate.
We match your CertainTeed roof line and color to the correct flashing profile, check the face height and drip lip against your existing metal, and get the right piece for your roof, OEM or quality aftermarket, whichever is the better buy. If your existing roof is GAF or Owens Corning, we source for those too. Call (844) 761-8186 and we’ll get the measurement started.
If your CertainTeed flashing has gone bad, don’t wait for the next storm to tell you how bad. Whether it’s a rusted drip edge or a leaking chimney line, we’ll come look at it, show you what we find, and give you a straight number in writing before we touch a thing. Standing offers of $40 Off Any Repair Over $200, a free second opinion on any written estimate, and 10% off for seniors and veterans all apply. Call (844) 761-8186 for a free estimate in Boulder City and the surrounding area. A live person answers around the clock, so you’re never stuck in a call center queue.
Written by the team at Shepherd & Sons Roofing Boulder City, serving Boulder City and nearby areas.