Owens Corning
Architectural shingles
Metal roofing
Tile roofing
GAF
Flat & low-slopeFree roof inspection with deck photos before we talk money - GAF and Owens Corning certified installation
Owens Corning Flashing Replacement: The Boulder City Owner’s Guide
Replacing failed flashing around an Owens Corning roof in Boulder City typically runs $285 – $650 installed per location, depending on whether we’re reworking a chimney, a sidewall, or a skylight curb, and most single-location jobs are finished in a day. We install Owens Corning-compatible flashing and reflash over existing Owens Corning shingles without pulling the whole roof. Homeowners here usually discover the problem the same way: a brown ring on the ceiling below a chimney, grit and granules washed into a downspout, or a roofer up on the roof for something else who points at lifted metal and says, “that’s been letting water in for a while.”

Key Takeaways
- Most Owens Corning flashing failures in Boulder City show up at chimneys, sidewalls, and skylight curbs first.
- We reflash over existing Owens Corning shingles instead of tearing the roof off.
- Installed price runs $285 – $650 per location; estimates are free.
- Every flashing job is backed by our written 90-Day Done Right Promise.
- An independent roofer, not affiliated with Owens Corning, installs the work.
Which Owens Corning Models This Applies To
Flashing isn’t part of the shingle warranty line – Owens Corning sells shingles, underlayments, and accessories, but the metal flashing at penetrations is either contractor-supplied or a generic accessory. That matters, because it means you don’t need to match a “flashing model” to a shingle model. You match the flashing to the penetration. What you do want to know is what’s underneath: a Duration shingle roof from the 2000s will have a different underlayment situation than a newer one, and how we detail flashing depends on the shingle course you’ve got.
Here’s how to identify what you have. Look in the attic or garage for a leftover shingle wrapper – Duration, Oakridge, Supreme, or Berkshire are the common Owens Corning lines we see on Boulder City roofs. Note the color, because a reflash on a sun-faded roof should land in the closest current color to avoid a bright patch. Then measure the penetration (chimney width, curb dimensions) so the metal can be cut before anyone climbs up. We stock neither flashing nor shingles on a truck; parts are ordered to the job, so the measurement call matters. If the old flashing was a generic galvanized step flashing, we can often upgrade to a heavier gauge or a soldered copper – that’s the aftermarket call worth making here.
Styles & brands we work with
- Architectural shingles
- Metal roofing
- Tile roofing
- GAF
- Owens Corning
- Flat & low-slope
Signs Your Owens Corning Flashing Replacement Is Failing
Flashing fails quietly. Here’s what we look for and what it usually means.
- Brown water stains on a ceiling or wall below the chimney. Water is getting behind the step flashing or the counterflashing, often where the sealant has cracked after years of Nevada sun cycling the metal.
- Granules and grit washing out of a downspout near a wall or curb. Water is running under the shingles instead of over them, scouring the mat and carrying granules with it – a sign the flashing is no longer shedding water out.
- Lifted, curled, or rusted metal at the penetration. Heat, UV, and thermal movement bend thin galvanized flashing over time; once it lifts, wind-driven rain blows in under it.
- Daylight or a visible gap in the attic where the roof meets a wall. That gap is a flashing detail that has separated, and it’s a direct path for water and pests.
- Moss, staining, or a soft spot near a chimney or skylight after a rain. Pooling water at a failed flashing detail is the classic tell; by the time you see it from below, the deck has usually been wet for a while.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Here’s what flashing replacement actually runs in Boulder City.

| Job | Typical Installed Range |
|---|---|
| Single sidewall or wall-to-roof detail | $285 – $425 |
| Chimney reflash (step + counterflashing) | $425 – $650 |
| Skylight curb reflash | $385 – $600 |
| Multiple penetrations or full-tie-in | Quoted per job |
The price covers tearing out the failed metal, inspecting and drying the deck if needed, new underlayment at the detail, new flashing set to the shingle course, re-sealing, and cleanup. What drives the range: accessibility, whether the deck is rotted, gauge or copper upgrade, and how many penetrations. Parts and labor are broken out on a written line-item estimate, so you see the metal’s cost separately from the work. Every flashing job carries our written 90-Day Done Right Promise – if it leaks, one call brings Bill back. Free second opinion on any written estimate you’ve already got.
DIY or Call Us?
You can safely check a few things: look for stains on ceilings and walls, check the attic for daylight at penetrations after a rain, and note lifted or rusted metal from the ground with binoculars. That’s diagnosis, not repair. Where DIY goes wrong is on the roof itself – flashing replacement means lifting shingle courses, working at height on a pitched surface, and getting the layering (underlayment, step flashing, shingle, counterflashing) in the right order. Get the order wrong and water finds it. On a two-story roof or a steep pitch, this is genuinely dangerous work, and we’d rather you didn’t. Call us at (844) 761-8186 and we’ll come look, no trip charge inside our own county.
FAQs
Galvanized flashing typically lasts 15 – 25 years here; copper can go 50+. Boulder City’s intense sun and dry heat cycle metal faster than a wetter climate does, so sealant joints often fail before the metal itself. Call (844) 761-8186 for an inspection – estimates are free.
Sometimes, yes. A failed sealant joint can be cleaned out and re-sealed; a fully lifted or rusted-through flashing needs replacement. We’ll tell you which one you’re looking at and show you the photos before we talk money.
Most single-location reflashes take half a day to a full day, weather permitting. Multiple penetrations or a rotted deck add time. Call for a real number once we see the roof.
We order flashing to the job’s measurements rather than carrying it on a truck, and we can upgrade to heavier gauge or copper if you want it. We install Owens Corning products alongside GAF and CertainTeed, so we know how the details go together.
If your flashing is failing, the sooner we look, the less deck damage you’ll pay for. Call Shepherd & Sons Roofing Boulder City at (844) 761-8186 for a free estimate – a live person answers, day or night, and we’ll be out to look.
Written by the team at Shepherd & Sons Roofing Boulder City, serving Boulder City and nearby areas.