Architectural shingles
Metal roofing
Tile roofing
GAF
Owens Corning
Flat & low-slopeFree roof inspection with deck photos before we talk money - GAF and Owens Corning certified installation
Tamko Gutter Replacement: The Boulder City Owner’s Guide
Quick answer: A Tamko gutter replacement section on a Boulder City home usually runs $18 – $34 per linear foot installed, and a single failed run is typically a one-day job once the right part is in hand. We install Tamko-compatible gutter components and don’t carry parts on a truck, so exact pricing comes from measuring your run, not from a phone guess.

Most owners here don’t go looking for the gutter. They find it during a wind event off the McCullough Range, when a hanger lets go and a full run of gutter peels away from the fascia with a load of water still in it. Or they notice the downspout has stopped draining and a stripe of discolored stucco is creeping up the wall after a monsoon cell dumps half an inch in twenty minutes. Either way, the part has usually been failing quietly for a season before anyone climbs a ladder.
Which Tamko Models This Applies To
Tamko makes several gutter lines, and the right replacement part depends on which one you have. The most common on Boulder City homes is Tamko’s K-style (also called ogee) gutter in 5-inch and 6-inch profiles, plus the half-round line on some older custom builds. Seamless extruded aluminum and steel sections dominate newer construction; a lot of the 1960s – 1990s housing stock around Boulder City has 5-inch K-style.
Identify your profile before you order anything. Measure the gutter’s outside width across the top opening – a 5-inch K-style reads about 5 inches across the face; a 6-inch reads about 6. Then look at the hanger bracket spacing and the downspout outlet size, because Tamko’s outlets and end caps are profile-specific and a 5-inch end cap will not seat on a 6-inch run. Any original labeling is usually long gone, so measurements are your ground truth.
On the OEM-versus-aftermarket question: Tamko-branded parts guarantee fit on a Tamko run, but a quality aftermarket aluminum K-style section built to the same 5-inch or 6-inch profile will seat correctly and often costs less. We’ll tell you honestly which makes sense for your run. We’re an independent service provider, not affiliated with Tamko, so we’re matching the profile, not protecting a brand.
Styles & brands we work with
- Architectural shingles
- Metal roofing
- Tile roofing
- GAF
- Owens Corning
- Flat & low-slope
Signs Your Tamko Gutter Replacement Is Failing
Here’s what actually tells you the run is done, and what’s causing it:
- Gutter pulling away from the fascia. The hanger screws have backed out of dry, sun-baked fascia board – common in Boulder City’s low-humidity climate, where wood checks and shrinks over a decade or two and the fastener loses its bite.
- Water sheeting over the front lip during rain. The gutter has lost its slope or the profile is sagging between hangers, so a monsoon downpour overwhelms a run that was pitched fine when it was new.
- Rust streaks or pinholes on steel sections. Standing water from a blocked slope has sat in the channel; the coating fails at the waterline and the steel starts pitting from the inside out.
- Downspout backing up at the outlet. The outlet seam has separated or the drop is undersized, so water backs into the gutter and overflows the nearest joint first.
- Staining or bubbling paint on the stucco below the run. The end cap or a hidden seam is leaking and water is tracking behind the fascia board, which is the expensive kind of failure – it rots framing before you see it from the ground.
If two or more of those are showing on the same run, replacing the section usually beats chasing individual leaks.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Typical installed range in Boulder City, itemized:

| Item | Installed range |
|---|---|
| 5-inch K-style aluminum gutter, per linear foot | $18 – $26 |
| 6-inch K-style aluminum gutter, per linear foot | $24 – $34 |
| Downspout, per linear foot | $9 – $16 |
| End caps, outlets, hangers (per piece) | $8 – $30 |
| Fascia repair if the board has rotted | $45 – $90 per linear foot |
The range is driven by profile size, run height (a two-story run costs more), how much fascia repair is needed, and whether we’re matching an existing color. You get a written line-item quote before anyone touches the roof – no change orders once the ladder is up. Workmanship is backed by the written 90-Day Done Right Promise, and if it’s not right, one call brings us back. Free second opinion on any written estimate you’re holding.
DIY or Call Us?
You can safely handle the checks from the ground and from a stable ladder: measure the profile, look for hangers pulling out of the fascia, check that downspouts run clear, and look for staining on the stucco. Those tell you what you have and whether it’s worth replacing a section.
What you shouldn’t do is hang a new full run off a ladder at gutter height on a two-story wall, or try to re-pitch a section without solid fascia to bite into. Gutter work at height is where owners get hurt – and a half-attached run is worse than the failing one, because it comes down in the first big wind with water weight behind it. Pulling the old section and mounting a new one from a proper setup takes a crew a few hours. Call (844) 761-8186 and we’ll get you a straight number on what your run needs.
FAQs
An aluminum Tamko gutter run in Boulder City typically lasts 20 – 30 years; painted steel runs last 15 – 25 and are more vulnerable to rust where water sits. The sun is the real enemy here – UV exposure and low humidity dry out fascia and bake the finish long before the metal gives out.
Sometimes – resealing a single failing seam or re-setting one hanger is often worth it. If the run has lost slope, has multiple separated seams, or the fascia behind it is soft, replacement is the better call and usually cheaper over five years. We’ll tell you which side you’re on.
A single failed run of K-style gutter is typically a one-day job for a crew, longer if fascia repair is involved. We give you the schedule up front after the measure – no “we’ll see how it goes.”
We measure your profile, confirm the size and outlet layout, and source the matching Tamko-compatible component – authentic Tamko where it makes sense, a quality aftermarket equivalent where the fit and price are better. We also install GAF, Owens Corning, and CertainTeed roofing products if the gutter work turns into a bigger roof repair.
Ready for a real number? Call (844) 761-8186 for a free estimate – a live person answers, day or night.
Written by the team at Shepherd & Sons Roofing Boulder City, serving Boulder City and nearby areas.